[0000.126] [TegraBoot] (version 00.00.2018.01-l4t-89b97a49) [0000.131] Processing in cold boot mode Bootloader 2 [0000.136] A02 Bootrom Patch rev = 1023 [0000.140] Power-up reason: pmc por [0000.143] No Battery Present [0000.145] pmic max77620 reset reason [0000.149] pmic max77620 NVERC : 0x40 [0000.152] RamCode = 0 [0000.154] Platform has DDR4 type RAM [0000.158] max77620 disabling SD1 Remote Sense [0000.162] Setting DDR voltage to 1125mv [0000.166] Serial Number of Pmic Max77663: 0x1012c3 [0000.174] Entering ramdump check [0000.177] Get RamDumpCarveOut = 0x0 [0000.180] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.185] Last reboot was clean, booting normally! [0000.190] Sdram initialization is successful [0000.194] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.200] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.206] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.212] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.229] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.235] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.251] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.257] Platform-DebugCarveout: 0 [0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.266] Non secure mode, and RB not enabled. [0000.391] Csd NumOfBlocks=62333952 [0000.396] Set High speed to 1 [0000.400] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWaitForCommandComplete func at 278 line [0000.410] Command complete wait failed with error 0x3 Interrupt 0x18001 [0000.416] Number of retries left 4 [0000.428] Using GPT Primary to query partitions [0000.435] Loading Tboot-CPU binary [0000.447] Verifying TBC in OdmNonSecureSBK mode [0000.457] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.464] Bootloader downloaded successfully. [0000.468] Downloaded Tboot-CPU binary to 0xa0000258 [0000.473] MAX77620_GPIO5 configured [0000.477] CPU power rail is up [0000.480] CPU clock enabled [0000.483] Performing RAM repair [0000.486] Updating A64 Warmreset Address to 0xa00002e9 [0000.491] Loading NvTbootBootloaderDTB [0000.529] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.594] Bootloader DTB Load Address: 0x83000000 [0000.599] Loading NvTbootKernelDTB [0000.636] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.701] Kernel DTB Load Address: 0x83100000 [0000.707] Loading cboot binary [0000.751] Verifying EBT in OdmNonSecureSBK mode [0000.794] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.801] Bootloader downloaded successfully. [0000.805] Next binary entry address: 0x92c00258 [0000.810] BoardId: 3448 [0000.814] Overriding pmu board id with proc board id [0000.819] Display board id is not available [0000.862] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.914] /bpmp deleted [0000.916] SC7EntryFw header found loaded at 0xff700000 [0001.104] OVR2 PMIC [0001.106] Bpmp FW successfully loaded [0001.112] WB0 init successfully at 0xff780000 [0001.117] Set NvDecSticky Bits [0001.120] GSC2 address ff53fffc value c0edbbcc [0001.126] GSC MC Settings done [0001.132] TOS Image length 53680 [0001.135] Monitor size 53680 [0001.138] OS size 0 [0001.148] Secure Os AES-CMAC Verification Success! [0001.152] TOS image cipher info: plaintext [0001.156] Loading and Validation of Secure OS Successful [0001.172] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.177] NvTbootPackSdramParams: start. [0001.182] NvTbootPackSdramParams: done. [0001.186] Tegraboot started after 53776 us [0001.190] Basic modules init took 789812 us [0001.194] NvTbootQspiFlashIoctl: Opcode = 1 not supported [0001.199] Sec Bootdevice Read Time = 622327755 ms, Read Size = 622327755 KB [0001.206] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.211] Storage Device Read Time = 182 ms, Read Size = 2241 KB [0001.217] Storage Device Write Time = 0 ms, Write Size = 0 KB [0001.222] Next stage binary read took 39561 us [0001.227] Carveout took -51221 us [0001.230] CPU initialization took 382640 us [0001.234] Total time taken by TegraBoot 1160792 us [0001.239] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):a28d87f09 NOTICE: BL31: Built : 16:52:46, Jul 16 2019 ERROR: Error initializing runtime service trusty_fast [0001.361] RamCode = 0 [0001.366] LPDDR4 Training: Read DT: Number of tables = 2 [0001.371] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.383] EMC Training Successful [0001.386] 408000 not found in DVFS table [0001.393] RamCode = 0 [0001.396] DT Write: emc-table@204000 succeeded [0001.402] DT Write: emc-table@1600000 succeeded [0001.406] LPDDR4 Training: Write DT: Number of tables = 2 [0001.449] [0001.450] Debug Init done [0001.452] Marked DTB cacheable [0001.455] Bootloader DTB loaded at 0x83000000 [0001.460] Marked DTB cacheable [0001.463] Kernel DTB loaded at 0x83100000 [0001.467] DeviceTree Init done [0001.479] Pinmux applied successfully [0001.483] gicd_base: 0x50041000 [0001.486] gicc_base: 0x50042000 [0001.489] Interrupts Init done [0001.494] Using base:0x60005090 & irq:208 for tick-timer [0001.499] Using base:0x60005098 for delay-timer [0001.503] platform_init_timer: DONE [0001.507] Timer(tick) Init done [0001.510] osc freq = 38400 khz [0001.514] [0001.516] welcome to cboot [0001.518] [0001.519] Cboot Version: 00.00.2018.01-t210-3a168c35 [0001.524] calling constructors [0001.527] initializing heap [0001.530] initializing threads [0001.533] initializing timers [0001.536] creating bootstrap completion thread [0001.540] top of bootstrap2() [0001.543] CPU: ARM Cortex A57 [0001.546] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.551] initializing platform [0001.554] Scratch reg 37 & 271 initial value set.. [0001.560] cboot:secure-pmc present [0001.563] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.568] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.572] Macronix QSPI chip present [0001.576] SPI device register [0001.579] init boot device [0001.581] allocating memory for boot device(SPI) [0001.586] registering boot device [0001.595] sdmmc node status = okay [0001.598] sdcard instance = 0 [0001.601] sdcard gpio handle 0x56 [0001.604] sdcard gpio pin 0xc9 [0001.607] sdcard gpio flags 0x0 [0001.610] vmmc-supply 0x99 [0001.613] Instance: 0 [0001.615] Allocating memory for context [0001.619] enabling clock [0001.621] sd card init [0001.624] Check card present and stable [0001.627] Send command 0 [0001.652] Send command 3 [0001.656] Set RCA for the card [0001.659] Query card specific data by command 9 [0001.666] Parse CSD data [0001.668] Send command 7 [0001.678] Calling sd device register [0001.682] Init sdcard [0001.684] Allocating memory for boot device [0001.688] Registering user device [0001.701] Enable APE clock [0001.704] Un-powergate APE partition [0001.707] of_register: registering tegra_udc to of_hal [0001.712] of_register: registering tegra_udc to of_hal [0001.718] of_register: registering inv20628-driver to of_hal [0001.723] of_register: registering ads1015-driver to of_hal [0001.729] of_register: registering lp8557-bl-driver to of_hal [0001.735] of_register: registering bq2419x_charger to of_hal [0001.740] of_register: registering cpc to of_hal [0001.745] of_register: registering bq27441_fuel_gauge to of_hal [0001.756] gpio framework initialized [0001.759] of_register: registering tca9539_gpio to of_hal [0001.765] of_register: registering tca9539_gpio to of_hal [0001.770] of_register: registering i2c_bus_driver to of_hal [0001.776] of_register: registering i2c_bus_driver to of_hal [0001.781] of_register: registering i2c_bus_driver to of_hal [0001.787] of_register: registering i2c_bus_driver to of_hal [0001.792] pmic framework initialized [0001.796] of_register: registering max77620_pmic to of_hal [0001.801] regulator framework initialized [0001.805] of_register: registering tps65132_bl_driver to of_hal [0001.811] initializing target [0001.817] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.826] fixed regulator driver initialized [0001.843] initializing OF layer [0001.846] NCK carveout not present [0001.849] Skipping dts_overrides [0001.853] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.870] I2C Bus Init done [0001.872] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.882] I2C Bus Init done [0001.885] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.895] I2C Bus Init done [0001.898] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.908] I2C Bus Init done [0001.911] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.921] I2C Bus Init done [0001.924] of_children_init: Ops found for compatible string maxim,max77620 [0001.934] max77620_init using irq 118 [0001.939] register 'maxim,max77620' pmic [0001.943] gpio_driver_register: register 'max77620-gpio' driver [0001.949] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.960] I2C Bus Init done [0001.963] NCK carveout not present [0001.966] shim_invoke: No NCT, Calling dts updates [0001.978] Find /i2c@7000c000's alias i2c0 [0001.982] get eeprom at 1-a0, size 256, type 0 [0001.990] Find /i2c@7000c500's alias i2c2 [0001.994] get eeprom at 3-a0, size 256, type 0 [0001.999] get eeprom at 3-ae, size 256, type 0 [0002.003] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.008] I2C slave not started [0002.011] I2C write failed [0002.014] Writing offset failed [0002.017] eeprom_init: EEPROM read failed [0002.021] pm_ids_update: eeprom init failed [0002.025] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.055] pm_ids_update: The pm board id is 3448-0000-200 [0002.062] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.069] pm_ids_update: pm id update successful [0002.074] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.104] pm_ids_update: The pm board id is 3449-0000-200 [0002.110] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0002.118] pm_ids_update: pm id update successful [0002.148] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.154] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.162] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.168] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.177] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e3:fa:48 [0002.183] Plugin Manager: Parse ODM data 0x00094000 [0002.193] shim_cmdline_install: /chosen/bootargs: console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 [0002.210] Find /i2c@7000c000's alias i2c0 [0002.213] get eeprom at 1-a0, size 256, type 0 [0002.222] Find /i2c@7000c500's alias i2c2 [0002.226] get eeprom at 3-a0, size 256, type 0 [0002.230] get eeprom at 3-ae, size 256, type 0 [0002.235] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.240] I2C slave not started [0002.243] I2C write failed [0002.246] Writing offset failed [0002.249] eeprom_init: EEPROM read failed [0002.253] pm_ids_update: eeprom init failed [0002.257] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.287] pm_ids_update: The pm board id is 3448-0000-200 [0002.294] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.300] pm_ids_update: pm id update successful [0002.305] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.335] pm_ids_update: The pm board id is 3449-0000-200 [0002.342] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0002.349] pm_ids_update: pm id update successful [0002.379] Chip UID is 000000016441b74510000000100183c0 [0002.384] Add serial number:04211190069460c08301 as DT property [0002.392] Applying platform configs [0002.399] platform-init is not present. Skipping [0002.403] calling apps_init() [0002.429] Found 16 GPT partitions in "sd0" [0002.433] Proceeding to Cold Boot [0002.436] starting app android_boot_app [0002.440] Device state: unlocked [0002.443] display console init [0002.451] could not find regulator [0002.475] hdmi cable not connected [0002.478] is_hdmi_needed: HDMI not connected, returning false [0002.484] hdmi is not DT entry for leds-pwm not found c[0002.492] onnected [0002.494] sor0 is not supported [0002.497] display_console_init: no valid display out_type [0002.505] subnode volume_up is not found ! [0002.509] subnode back is not found ! [0002.512] subnode volume_down is not found ! [0002.517] subnode menu is not found ! [0002.520] Gpio keyboard init success [0002.532] blob_init: BMP partition does not have valid Blob [0002.537] load_bmp_blob: BMP blob initialization failed [0002.543] Could not load/initialize BMP blob...ignoring [0002.582] decompressor handler not found [0002.586] load_firmware_blob: Firmware blob loaded, entries=2 [0002.591] se_aes_verify_sbk_clear: Error [0002.595] bl_battery_charging: connected to external power supply [0002.603] xusb is supported [0002.609] error while finding nvidia,portmap [0002.614] could not find regulator [0003.117] xusb blob version 0 size 124416 [0003.121] firmware size 124416 [0003.126] Firmware timestamp: 0x5cd2a472, Version: 50.22 release [0003.136] xhci0: 64 bytes context size, 32-bit DMA [0003.176] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.196] uhub0: on usbus0 [0003.846] uhub0: 9 ports with 9 removable, self powered [0004.846] failed to get HID devices [0004.849] failed to init xhci or no usb device attached [0004.857] display_console_ioctl: No display init [0004.861] switch_backlight failed [0004.864] device_query_partition_size: failed to open partition sd0:MSC ! [0004.871] MSC Partition not found [0004.874] device_query_partition_size: failed to open partition sd0:USP ! [0004.881] USP partition read failed! [0004.885] blob_init: blob-partition USP header read failed [0004.890] android_boot Unable to update recovery partition [0004.896] kfs_getpartname: name = LNX [0004.899] Loading kernel from LNX [0004.957] Verifying boot image in OdmNonSecureSBK mode [0005.000] kernel load address: 0x80080000, size: 488210 bytes [0005.006] ramdisk load address: 0x84100000, size: 0 bytes [0005.011] load kernel from storage [0005.023] decompressor handler not found [0005.081] Successfully loaded kernel and ramdisk images [0005.096] blob_init: BMP partition does not have valid Blob [0005.101] load_bmp_blob: BMP blob initialization failed [0005.106] bmp blob is not loaded and initialized [0005.111] Failed to display boot-logo [0005.114] NCK carveout not present [0005.118] Skipping dts_overrides [0005.121] NCK carveout not present [0005.124] shim_invoke: No NCT, Calling dts updates [0005.135] Find /i2c@7000c000's alias i2c0 [0005.139] get eeprom at 1-a0, size 256, type 0 [0005.148] Find /i2c@7000c500's alias i2c2 [0005.152] get eeprom at 3-a0, size 256, type 0 [0005.156] get eeprom at 3-ae, size 256, type 0 [0005.161] pm_ids_update: Updating 1,a0, size 256, type 0 [0005.166] I2C slave not started [0005.169] I2C write failed [0005.172] Writing offset failed [0005.175] eeprom_init: EEPROM read failed [0005.179] pm_ids_update: eeprom init failed [0005.183] pm_ids_update: Updating 3,a0, size 256, type 0 [0005.213] pm_ids_update: The pm board id is 3448-0000-200 [0005.219] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0005.227] pm_ids_update: pm id update successful [0005.232] pm_ids_update: Updating 3,ae, size 256, type 0 [0005.262] pm_ids_update: The pm board id is 3449-0000-200 [0005.268] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0005.276] pm_ids_update: pm id update successful [0005.306] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.312] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.320] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.326] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.334] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e3:fa:48 [0005.341] Plugin Manager: Parse ODM data 0x00094000 [0005.351] shim_cmdline_install: /chosen/bootargs: console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 [0005.361] Add serial number:04211190069460c08301 as DT property [0005.370] "bpmp" doesn't exist, creating [0005.376] Updated bpmp info to DTB [0005.381] Updated initrd info to DTB [0005.384] "proc-board" doesn't exist, creating [0005.390] Updated board info to DTB [0005.393] "pmu-board" doesn't exist, creating [0005.398] Updated board info to DTB [0005.402] "display-board" doesn't exist, creating [0005.407] Updated board info to DTB [0005.411] "reset" doesn't exist, creating [0005.415] Updated reset info to DTB [0005.419] display_console_ioctl: No display init [0005.423] display_console_ioctl: No display init [0005.428] display_console_ioctl: No display init [0005.432] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 [0005.466] DTB cmdline: console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 [0005.474] Updated bootarg info to DTB [0005.478] Adding uuid 000000016441b74510000000100183c0 to DT [0005.484] Adding eks info 0 to DT [0005.489] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.495] Updated memory info to DTB [0005.501] Updated system-lp0-disable info to DTB [0005.509] set vdd_core voltage to 1075 mv [0005.513] setting 'vdd-core' regulator to 1075000 micro volts [0005.536] could not find regulator [0005.540] Found secure-pmc; disable BPMP U-Boot 2016.07 (Sep 16 2019 - 09:32:17 +0000) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** Hit any key to stop autoboot: 0 Scanning mmc devices 0 1 2 Card did not respond to voltage select! ** Bad device mmc 0 ** Card did not respond to voltage select! ** Bad device mmc 0 ** reading resin-image-flasher ** Unable to read file resin-image-flasher ** reading resin-image 24 bytes read in 11 ms (2 KiB/s) MMC Device 2 not found ** Bad device mmc 2 ** Found resin image on mmc 1 Loading resinOS_uEnv.txt from mmc device 1 partition 0xC reading resinOS_uEnv.txt ** Unable to read file resinOS_uEnv.txt ** Loading bootcount.env from mmc device 1 partition 0xC reading bootcount.env ** Unable to read file bootcount.env ** No bootcount.env file. Setting bootcount=0 in environment switch to partitions #0, OK mmc1 is current device Scanning mmc 1:c... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 188 bytes read in 12 ms (14.6 KiB/s) Boot Options 1: primary Image 1: primary Image Retrieving file: /Image reading /Image 39729160 bytes read in 1770 ms (21.4 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 root=PARTUUID=04aa9f84-4959-4ce8-b73e-080ccb43132f ro rootwait ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 000000008317724e Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-l4t-r32.2+g3dcbed5 (oe-user@oe-host) (gcc version 8.3.0 (GCC) ) #1 SMP PREEMPT Mon Sep 16 12:11:43 UTC 2019 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb3000 s61848 r8192 d32360 u102400 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 console=ttyS0,115200 console=tty0 fbcon=map:0 net.ifnames=0 root=PARTUUID=04aa9f84-4959-4ce8-b73e-080ccb43132f ro rootwait [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29700(90%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3570388K/4159488K available (14974K kernel code, 2894K rwdata, 9592K rodata, 11264K init, 601K bss, 113964K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f20000 ( 14976 KB) [ 0.000000] .rodata : 0xffffff8008f20000 - 0xffffff8009890000 ( 9664 KB) [ 0.000000] .init : 0xffffff8009890000 - 0xffffff800a390000 ( 11264 KB) [ 0.000000] .data : 0xffffff800a390000 - 0xffffff800a663808 ( 2895 KB) [ 0.000000] .bss : 0xffffff800a663808 - 0xffffff800a6f9d64 ( 602 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001532] Console: colour dummy device 80x25 [ 0.002369] console [tty0] enabled [ 0.002411] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.002442] pid_max: default: 32768 minimum: 301 [ 0.002899] Security Framework initialized [ 0.003133] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003156] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.004324] ftrace: allocating 46499 entries in 182 pages [ 0.173675] ASID allocator initialised with 65536 entries [ 0.211774] tegra-id: chipid=22117. [ 0.211820] tegra-id: opt_subrevision=0. [ 0.211847] Tegra Speedo/IDDQ fuse revision 4 [ 0.211862] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.211877] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.211892] Tegra: CPU Speedo Value 2074, SoC Speedo Value 1989, GPU Speedo Value 2083 [ 0.211913] Tegra: CPU IDDQ Value 1972, SoC IDDQ Value 2280, GPU IDDQ Value 2795 [ 0.211947] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.211975] DTS File Name: /yocto/resin-board/build/tmp/work-shared/jetson-nano/kernel-source/arch/arm64/boot/dts/../../../../nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts [ 0.212010] DTB Build time: Sep 16 2019 12:18:50 [ 0.261006] CPU1: Booted secondary processor [411fd071] [ 0.292922] CPU2: Booted secondary processor [411fd071] [ 0.324902] CPU3: Booted secondary processor [411fd071] [ 0.324988] Brought up 4 CPUs [ 0.325055] SMP: Total of 4 processors activated. [ 0.325072] CPU features: detected feature: 32-bit EL0 Support [ 0.325346] CPU: All CPU(s) started at EL2 [ 0.325377] alternatives: patching kernel code [ 0.333410] devtmpfs: initialized [ 0.368290] Initilizing CustomIPI irq domain [ 0.368663] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.368708] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.379157] pinctrl core: initialized pinctrl subsystem [ 0.379744] OS set in device tree is not L4T. [ 0.380052] regulator-dummy: no parameters [ 0.380284] Initializing plugin-manager [ 0.380384] Plugin module not found [ 0.380616] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.381237] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.382116] node /plugin-manager/fragment@5 match with board 3449-0000-200 [ 0.382543] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt [ 0.382972] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt [ 0.383365] node /plugin-manager/fragement@9 match with board <3448-0000-300 [ 0.387839] NET: Registered protocol family 16 [ 0.389081] pstore: using zlib compression [ 0.389772] console [pstore-1] enabled [ 0.389790] pstore: Registered ramoops as persistent store backend [ 0.389810] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.401020] cpuidle: using governor menu [ 0.404696] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.406055] vdso: 2 pages (1 code @ ffffff8008f27000, 1 data @ ffffff800a394000) [ 0.406100] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.409407] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.411857] tegra_powergate_init: DONE [ 0.411894] DTS File Name: /yocto/resin-board/build/tmp/work-shared/jetson-nano/kernel-source/arch/arm64/boot/dts/../../../../nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts [ 0.411930] DTB Build time: Sep 16 2019 12:18:50 [ 0.413474] Tegra reboot handler registered. [ 0.417645] iommu: Adding device tegra-carveouts to group 0 [ 0.417811] platform tegra-carveouts: domain=ffffffc0f9b55318 allocates as[0]=ffffffc0f9b680a8 [ 0.418157] iommu: Adding device smmu_test to group 1 [ 0.418217] platform smmu_test: domain=ffffffc0f9b55558 allocates as[0]=ffffffc0f9b68110 [ 0.418994] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.419072] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.419139] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.419164] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.419198] mc-err: mcerr ops are set to t21x [ 0.428271] iommu: Adding device 70090000.xusb to group 2 [ 0.428588] iommu: Adding device 70006000.serial to group 3 [ 0.428666] platform 70006000.serial: domain=ffffffc0f9bb6c18 allocates as[0]=ffffffc0f9b68178 [ 0.429088] iommu: Adding device 70006040.serial to group 4 [ 0.429344] iommu: Adding device 70006200.serial to group 5 [ 0.429536] iommu: Adding device sound to group 6 [ 0.429600] platform sound: domain=ffffffc0f941f198 allocates as[0]=ffffffc0f9b681e0 [ 0.430115] iommu: Adding device 7000d400.spi to group 7 [ 0.430370] iommu: Adding device 7000d600.spi to group 8 [ 0.430664] iommu: Adding device 70410000.spi to group 9 [ 0.430957] iommu: Adding device 50000000.host1x to group 10 [ 0.431236] iommu: Adding device 54080000.vi to group 11 [ 0.431615] iommu: Adding device 54600000.isp to group 12 [ 0.431877] iommu: Adding device 54680000.isp to group 13 [ 0.432154] iommu: Adding device tegradc.0 to group 14 [ 0.432216] platform tegradc.0: domain=ffffffc0f942c0d8 allocates as[0]=ffffffc0f9b68248 [ 0.432747] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.433087] iommu: Adding device tegradc.1 to group 15 [ 0.433151] platform tegradc.1: domain=ffffffc0f942c318 allocates as[0]=ffffffc0f9b682b0 [ 0.433665] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.433921] iommu: Adding device 54340000.vic to group 16 [ 0.434119] iommu: Adding device 544c0000.nvenc to group 17 [ 0.434316] iommu: Adding device 54500000.tsec to group 18 [ 0.434504] iommu: Adding device 54100000.tsecb to group 19 [ 0.434703] iommu: Adding device 54480000.nvdec to group 20 [ 0.434890] iommu: Adding device 54380000.nvjpg to group 21 [ 0.435858] iommu: Adding device 546c0000.i2c to group 22 [ 0.436183] iommu: Adding device 57000000.gpu to group 23 [ 0.436250] platform 57000000.gpu: domain=ffffffc0f9436318 allocates as[0]=ffffffc0f9b68318 [ 0.436325] platform 57000000.gpu: domain=ffffffc0f9436318 allocates as[1]=ffffffc0f9b68380 [ 0.436384] platform 57000000.gpu: domain=ffffffc0f9436318 allocates as[2]=ffffffc0f9b683e8 [ 0.436436] platform 57000000.gpu: domain=ffffffc0f9436318 allocates as[3]=ffffffc0f9b68450 [ 0.437259] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.437300] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.437326] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.437345] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.437362] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.489181] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.489213] tegra-pmc: Clear bootloader IO dpd settings [ 0.489246] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.489325] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.489614] iommu: Adding device 70012000.se to group 24 [ 0.490332] iommu: Adding device 7000c000.i2c to group 25 [ 0.490586] iommu: Adding device 7000c400.i2c to group 26 [ 0.490830] iommu: Adding device 7000c500.i2c to group 27 [ 0.491076] iommu: Adding device 7000c700.i2c to group 28 [ 0.491347] iommu: Adding device 7000d000.i2c to group 29 [ 0.491604] iommu: Adding device 7000d100.i2c to group 30 [ 0.491891] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.491959] platform sdhci-tegra.0: domain=ffffffc0f94df498 allocates as[0]=ffffffc0f9b684b8 [ 0.492727] iommu: Adding device 700d0000.xudc to group 32 [ 0.495811] vdd-ac-bat: 5000 mV [ 0.496144] vdd-5v0-sys: 5000 mV [ 0.496961] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.497049] vdd-5v0-hdmi: 5000 mV [ 0.497436] vdd-1v8-sys: 1800 mV [ 0.497844] vdd-fan: supplied by vdd-5v0-sys [ 0.497896] vdd-fan: 5000 mV [ 0.498254] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.498302] vdd-usb-vbus: 5000 mV [ 0.498764] vdd-usb-vbus2: 5000 mV [ 0.521718] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.524119] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.525296] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.525334] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.525673] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.533140] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.533449] SCSI subsystem initialized [ 0.533899] usbcore: registered new interface driver usbfs [ 0.533962] usbcore: registered new interface driver hub [ 0.534047] usbcore: registered new device driver usb [ 0.537314] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.540285] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.541150] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.544198] vdd-ddr-1v1: 1150 mV [ 0.548197] vdd-pre-reg-1v35: 1350 mV [ 0.548920] random: fast init done [ 0.552196] vdd-1v8: 1800 mV [ 0.556196] avdd-sys-1v2: 1200 mV [ 0.560197] vdd-pex-1v0: 1050 mV [ 0.560799] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.561303] max77620-ldo3: at 3100 mV [ 0.564201] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.564680] max77620-ldo5: at 3100 mV [ 0.565178] max77620-ldo6: at 2800 mV [ 0.568202] avdd-1v05-pll: 1050 mV [ 0.572195] avdd-io-hdmi-dp: 1050 mV [ 0.573299] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.573605] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.574920] max77620 4-003c: max77620 probe successful [ 0.577429] media: Linux media interface: v0.10 [ 0.577496] Linux video capture interface: v2.00 [ 0.578292] pps_core: LinuxPPS API ver. 1 registered [ 0.578317] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.578350] PTP clock support registered [ 0.581891] tegra_fiq_debugger_init: found FIQ source (IRQ 98) [ 0.588027] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.588728] Advanced Linux Sound Architecture Driver Initialized. [ 0.589338] Bluetooth: Core ver 2.22 [ 0.589391] NET: Registered protocol family 31 [ 0.589409] Bluetooth: HCI device and connection manager initialized [ 0.589438] Bluetooth: HCI socket layer initialized [ 0.589463] Bluetooth: L2CAP socket layer initialized [ 0.589498] Bluetooth: SCO socket layer initialized [ 0.591149] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.591189] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.591253] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.591282] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.594095] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.595065] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.595169] vdd-3v3-sys: 3300 mV [ 0.595414] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.596274] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.596736] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.596786] vdd-3v3-sd: 3300 mV [ 0.597729] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.597784] avdd-io-edp-1v05: 1050 mV [ 0.598220] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.598271] vdd-usb-hub-en: 5000 mV [ 0.599415] camchar: rtcpu character device driver loaded [ 0.599982] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.601099] clocksource: Switched to clocksource arch_sys_counter [ 0.640363] VFS: Disk quotas dquot_6.6.0 [ 0.640535] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.640980] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.641597] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.641646] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.641919] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.641948] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.641979] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.642029] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.642057] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.642087] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.642112] nvmap_page_pool_init: Total RAM pages: 1011381 [ 0.642129] nvmap_page_pool_init: nvmap page pool size: 126422 pages (493 MB) [ 0.642257] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.642522] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.643333] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.650827] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.651225] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.651464] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.651674] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.651856] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.652131] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.652151] pre_t19x_iso_plat_init(): max_iso_bw=33280000KB [ 0.652590] NET: Registered protocol family 2 [ 0.653571] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.653804] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.654280] TCP: Hash tables configured (established 32768 bind 32768) [ 0.654444] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.654543] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.654931] NET: Registered protocol family 1 [ 0.655688] RPC: Registered named UNIX socket transport module. [ 0.655714] RPC: Registered udp transport module. [ 0.655730] RPC: Registered tcp transport module. [ 0.655748] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.855684] Trying to unpack rootfs image as initramfs... [ 0.865352] host1x 50000000.host1x: initialized [ 0.867008] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.870784] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.880149] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.881410] 9p: Installing v9fs 9p2000 file system support [ 0.884645] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.884818] io scheduler noop registered [ 0.885198] io scheduler cfq registered (default) [ 0.887547] gic 702f9000.agic: GIC IRQ controller registered [ 0.890583] iommu: Adding device 702ef000.adsp to group 33 [ 0.897170] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 0.897328] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 0.897817] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x9268c11 [ 0.897847] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 0.899423] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 0.899537] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 0.899643] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 0.899826] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 0.899929] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 0.900028] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 0.900130] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 0.900228] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 0.900329] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 0.900424] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 0.905668] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 0.907266] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 0.909000] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 0.910343] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 0.910714] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 0.911791] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.912043] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000 [ 0.912288] Adding domain tsec-pd to PM domain host1x-pd [ 0.914536] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 0.915349] tsec 54500000.tsec: initialized [ 0.916844] tsec 54100000.tsecb: initialized [ 0.917531] Adding domain nvdec-pd to PM domain host1x-pd [ 0.920734] nvdec 54480000.nvdec: initialized [ 0.921750] Adding domain vic03-pd to PM domain host1x-pd [ 0.921961] Adding domain msenc-pd to PM domain host1x-pd [ 0.922138] Adding domain nvjpg-pd to PM domain host1x-pd [ 0.925927] falcon 54340000.vic: initialized [ 0.927161] falcon 544c0000.nvenc: initialized [ 0.928450] falcon 54380000.nvjpg: initialized [ 0.932570] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 0.932701] display board info: id 0x0, fab 0x0 [ 0.932778] generic_infoframe_type: 0x87 [ 0.932919] tegradc tegradc.0: DT parsed successfully [ 0.932977] tegradc tegradc.0: Display dc.ffffff800b080000 registered with id=0 [ 0.936157] tegradc tegradc.0: probed [ 0.939585] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.943485] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 10 channels [ 0.944161] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 0.944455] kfuse 7000fc00.kfuse: initialized [ 0.945853] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 0.946783] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 0.947999] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 0.948034] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 0.948514] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 0.949845] vdd-gpu: applied init 1000000uV constraint [ 0.949876] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 0.950270] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 0.954346] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.954529] No Device Node present for smmu client: serial8250 !! [ 0.954559] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.954633] iommu: Adding device serial8250 to group 35 [ 0.956699] console [ttyS0] disabled [ 0.956790] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.401588] tegra-pcie 1003000.pcie: link 0 down, retrying [ 1.805812] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.210065] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.212082] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.318162] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.318172] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.318176] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.318181] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.318186] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.318550] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.329272] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 2.329277] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.329287] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit] [ 2.329308] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit] [ 2.329326] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.329337] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.329342] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.329350] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] [ 2.329709] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.329713] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 3.281519] console [ttyS0] enabled [ 3.281824] Console: switching to colour frame buffer device 80x30 [ 3.291763] tegradc tegradc.0: fb registered [ 3.297067] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.297407] serial-tegra 70006200.serial: RX in PIO mode [ 3.297498] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.298407] [drm] Initialized [ 3.324937] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 3.326543] brd: module loaded [ 3.331837] loop: module loaded [ 3.331925] tegra_profiler: version: 1.134, samples/io: 47/26 [ 3.332029] tegra_profiler: auth: init [ 3.333200] THERMAL EST: found 2 subdevs [ 3.333207] THERMAL EST num_resources: 0 [ 3.333212] [THERMAL EST subdev 0] [ 3.333219] [THERMAL EST subdev 1] [ 3.333628] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.333630] THERMAL EST: thz register success. [ 3.333804] THERMAL EST: end of probe, return err: 0 [ 3.334776] hisi_sas: driver version v1.6 [ 3.338471] tegra-qspi 70410000.spi: Prod settings list not found [ 3.339654] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 3.339662] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 3.342247] libphy: Fixed MDIO Bus: probed [ 3.342700] tun: Universal TUN/TAP device driver, 1.6 [ 3.342702] tun: (C) 1999-2004 Max Krasnyansky [ 3.343419] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.343425] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.343468] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.343469] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.343511] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.343513] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.343551] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 3.343553] Copyright(c) 1999 - 2017 Intel Corporation. [ 3.344325] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 3.344352] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.358488] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.358637] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e3:fa:48 from device tree [ 3.359117] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.359181] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.359181] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.359181] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.359640] PPP generic driver version 2.4.2 [ 3.359818] PPP BSD Compression module registered [ 3.359822] PPP Deflate Compression module registered [ 3.359861] PPP MPPE Compression module registered [ 3.359867] NET: Registered protocol family 24 [ 3.360038] VFIO - User Level meta-driver version: 0.3 [ 3.366673] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.366703] ehci-pci: EHCI PCI platform driver [ 3.366742] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.366753] ohci-pci: OHCI PCI platform driver [ 3.366784] ohci-platform: OHCI generic platform driver [ 3.369400] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.370001] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.371167] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f96fe800 id [ 3.372323] usbcore: registered new interface driver uas [ 3.372379] usbcore: registered new interface driver usb-storage [ 3.372475] usbcore: registered new interface driver usbserial [ 3.375452] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.376817] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.376830] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 3.376872] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.377151] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-05-08 09:42:10 UTC, Version: 50.22 release [ 3.377217] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.377229] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.377257] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.377921] mousedev: PS/2 mouse device common for all mice [ 3.377989] usbcore: registered new interface driver xpad [ 3.378148] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.378207] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.378430] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.378437] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.378442] usb usb1: Product: xHCI Host Controller [ 3.378446] usb usb1: Manufacturer: Linux 4.9.140-l4t-r32.2+g3dcbed5 xhci-hcd [ 3.378450] usb usb1: SerialNumber: 70090000.xusb [ 3.378963] hub 1-0:1.0: USB hub found [ 3.379009] hub 1-0:1.0: 5 ports detected [ 3.379782] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.379796] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.379871] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.379954] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.379959] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.379963] usb usb2: Product: xHCI Host Controller [ 3.379966] usb usb2: Manufacturer: Linux 4.9.140-l4t-r32.2+g3dcbed5 xhci-hcd [ 3.379970] usb usb2: SerialNumber: 70090000.xusb [ 3.380397] hub 2-0:1.0: USB hub found [ 3.380424] hub 2-0:1.0: 4 ports detected [ 3.481166] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 3.506057] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.508449] rtc rtc1: alarm rtc device [ 3.508470] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 3.508504] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.509064] i2c /dev entries driver [ 3.510568] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.533900] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.533971] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.534003] imx219 6-0010: board setup failed [ 3.534108] imx219: probe of 6-0010 failed with error -121 [ 3.534877] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 3.537223] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 3.537227] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 3.537657] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.537673] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 3.537681] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 3.537814] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.537823] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 3.537829] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 3.537976] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.537986] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 3.537992] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 3.538166] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 3.538959] tegra_aotag tegra-aotag: Registering sensor 0 [ 3.539013] tegra_aotag tegra-aotag: Invalid temp readout [ 3.539040] tegra_aotag tegra-aotag: Invalid temp readout [ 3.539056] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 3.539066] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 3.539876] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.539895] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 3.540053] tegra_aotag tegra-aotag: Invalid temp readout [ 3.540080] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 3.540446] parse_throttle_dt_data: Num cap clks = 6 [ 3.540451] parse_throttle_dt_data: clk=cclk_g type=2 [ 3.540463] parse_throttle_dt_data: clk=gpu type=4 [ 3.540485] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 3.540502] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 3.540522] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 3.540525] parse_throttle_dt_data: clk=emc type=3 [ 3.540882] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.540971] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.541143] tegra_throttle_probe: probe successful. #cdevs=4 [ 3.541828] FAN dev name: pwm-fan [ 3.541877] FAN:gpio request success. [ 3.541955] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 3.542230] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 3.542446] pwm_fan_driver pwm-fan: fan tach request irq success [ 3.542457] pwm_fan_driver pwm-fan: tach period: 1000 [ 3.542558] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 3.542563] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 3.542567] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 3.542571] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 3.542576] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 3.542580] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 3.542584] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 3.542588] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 3.542592] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 3.542596] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 3.543590] device-mapper: uevent: version 1.0.3 [ 3.544078] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 3.549255] tegra210-cpufreq cpufreq: probe()...completed [ 3.550111] sdhci: Secure Digital Host Controller Interface driver [ 3.550113] sdhci: Copyright(c) Pierre Ossman [ 3.550115] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.550725] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 3.551190] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 3.551375] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 3.555655] tegra-se 70012000.se: tegra_se_probe: complete [ 3.556141] hidraw: raw HID events driver (C) Jiri Kosina [ 3.557045] usbcore: registered new interface driver usbhid [ 3.557046] usbhid: USB HID core driver [ 3.559002] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 3.559154] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 3.560763] nvpmodel: initialized successfully [ 3.561783] usbcore: registered new interface driver snd-usb-audio [ 3.561837] No Device Node present for smmu client: snd-soc-dummy !! [ 3.561841] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.561861] iommu: Adding device snd-soc-dummy to group 36 [ 3.567377] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 3.590721] OPE platform probe [ 3.590807] OPE platform probe successful [ 3.591191] OPE platform probe [ 3.591271] OPE platform probe successful [ 3.597316] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 3.616488] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 3.616615] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 3.616742] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 3.616865] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 3.616985] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 3.617125] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 3.617252] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 3.617377] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 3.617503] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 3.617624] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 3.629323] u32 classifier [ 3.629325] Actions configured [ 3.629520] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3.666023] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.675051] Initializing XFRM netlink socket [ 3.675734] NET: Registered protocol family 10 [ 3.676499] NET: Registered protocol family 17 [ 3.676509] NET: Registered protocol family 15 [ 3.676581] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.676699] Bluetooth: RFCOMM socket layer initialized [ 3.676710] Bluetooth: RFCOMM ver 1.11 [ 3.676715] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 3.676720] Bluetooth: HIDP socket layer initialized [ 3.676738] 9pnet: Installing 9P2000 support [ 3.676768] Key type dns_resolver registered [ 3.680709] Registered cp15_barrier emulation handler [ 3.686172] Registered setend emulation handler [ 3.703146] registered taskstats version 1 [ 3.703702] Adding domain ve2-pd to PM domain host1x-pd [ 3.703943] Adding domain ve-pd to PM domain host1x-pd [ 3.717102] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 3.752083] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 3.752087] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.752090] usb 1-2: Product: 4-Port USB 2.1 Hub [ 3.752093] usb 1-2: Manufacturer: Generic [ 3.753529] hub 1-2:1.0: USB hub found [ 3.754602] hub 1-2:1.0: 4 ports detected [ 3.797164] mmc0: hw tuning done ... [ 3.797205] mmc0: new ultra high speed SDR104 SDHC card at address aaaa [ 3.797621] mmcblk0: mmc0:aaaa SC32G 29.7 GiB [ 3.803176] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.803178] GPT:2670591 != 62333951 [ 3.803180] GPT:Alternate GPT header not at the end of the disk. [ 3.803181] GPT:2670591 != 62333951 [ 3.803182] GPT: Use GNU Parted to correct GPT errors. [ 3.803207] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 [ 3.885105] tegra-xusb-padctl 7009f000.xusb_padctl: power down UTMI pad 1 [ 3.905108] usb 1-2: usb_suspend_both: status 0 [ 3.905182] usb usb1: usb_suspend_both: status 0 [ 4.627081] tegradc tegradc.1: No lt-data, using default setting [ 4.633103] tegradc tegradc.1: No hpd-gpio in DT [ 4.637738] tegradc tegradc.1: DT parsed successfully [ 4.642811] tegradc tegradc.1: Display dc.ffffff800da00000 registered with id=1 [ 4.650860] tegradc tegradc.1: dpd enable lookup fail:-19 [ 5.161918] Host read timeout at address 545c00c4 [ 5.163125] tegradc tegradc.1: probed [ 5.171220] tegradc tegradc.1: fb registered [ 5.178620] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 5.185757] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 5.186875] isp 54600000.isp: initialized [ 5.187795] isp 54680000.isp: initialized [ 5.198205] last reset is due to power on reset [ 5.198208] KERNEL: PMC reset status reg: 0x0 [ 5.198335] BL: PMC reset status reg: 0x0 [ 5.198337] BL: PMIC poweroff Event Recorder: 0x40 [ 5.199747] clk_cbus_recalc_rate: no gbus parent [ 5.199752] clk_cbus_round_rate: no gbus parent [ 5.199753] clk_cbus_round_rate: no gbus parent [ 5.199758] clk_cbus_recalc_rate: no gbus parent [ 5.199846] clk_cbus_recalc_rate: no gbus parent [ 5.199849] clk_cbus_round_rate: no gbus parent [ 5.199850] clk_cbus_round_rate: no gbus parent [ 5.199853] clk_cbus_recalc_rate: no gbus parent [ 5.199866] tegra_dvfs: GPU-cap: registered [ 5.199922] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 5.199924] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 5.199926] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled [ 5.201302] tegra_dvfs: vdd-gpu-vts: registered [ 5.201999] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 5.202589] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 5.203126] input: gpio-keys as /devices/gpio-keys/input/input1 [ 5.237560] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:15 UTC (946688415) [ 5.238584] vi 54080000.vi: vi_probe: ++ [ 5.241175] vi 54080000.vi: initialized [ 5.243197] vi 54080000.vi: subdev nvcsi--1 bound [ 5.243406] mmcblk mmc0:aaaa: Card claimed for testing. [ 5.244655] Disable partitions left on by BL [ 5.244658] disb [ 5.244700] bwmgr: missing cdev-type property [ 5.244785] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.244791] DRAM derating cdev registered. [ 5.245782] vdd-fan: disabling [ 5.245784] vdd-usb-vbus: disabling [ 5.245786] vdd-usb-vbus2: disabling [ 5.245795] avdd-io-edp-1v05: disabling [ 5.245950] ALSA device list: [ 5.245953] #0: tegra-hda at 0x70038000 irq 83 [ 5.245955] #1: tegra-snd-t210ref-mobile-rt565x [ 5.391245] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 5.396801] tegradc tegradc.1: blank - powerdown [ 5.401433] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 5.401435] Extcon DP: HPD disabled [ 5.401436] hpd: hpd_switch 0 [ 5.401439] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 5.401446] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 5.401450] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 5.438660] Freeing unused kernel memory: 11264K [ 7.662749] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 7.668770] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 7.929622] CP437: Invalid argument [ 7.976338] fsck.fat 4.1 (2017-01-24) [ 7.976338] /dev/disk/by-label/resin-boot: 27 files, 20275/40871 clusters [ 7.994237] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 8.009390] resin-rootA: clean, 4912/60960 files, 368305/487424 blocks[ 8.015808] [ 8.037698] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 8.044612] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 8.051839] usb 2-1: Product: 4-Port USB 3.1 Hub [ 8.056526] usb 2-1: Manufacturer: Generic [ 8.067472] hub 2-1:1.0: USB hub found [ 8.072819] resin-rootB: clean, 11/60960 files, 18278/487424 blocks[ 8.079010] hub 2-1:1.0: 4 ports detected [ 8.083215] [ 8.101008] resin-state: clean, 11/5136 files, 1849/20480 blocks[ 8.106954] [ 8.192093] Warning[ 8.194081] : [ 8.249127] usb 2-1: usb_suspend_both: status 0 [ 8.254134] usb usb2: usb_suspend_both: status 0 [ 9.532279] random: crng init done [ 9.969180] tegra-xusb 70090000.xusb: entering ELPG [ 9.975385] tegra-pmc: PMC tegra_pmc_utmi_phy_enable_sleepwalk : port 1, speed 3 [ 9.983087] tegra-pmc: PMC tegra_pmc_utmi_phy_enable_sleepwalk : port 2, speed 0 [ 9.992296] tegra-xusb 70090000.xusb: entering ELPG done [ 10.449556] EXT4-fs (mmcblk0p13): couldn't mount as ext3 due to feature incompatibilities [ 10.493855] EXT4-fs (mmcblk0p13): couldn't mount as ext2 due to feature incompatibilities [ 10.509291] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: (null) [ 10.566003] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: (null) [ 10.874752] switch_root: 6 output lines suppressed due to ratelimiting [ 11.012056] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null) [ 11.153047] systemd[1]: System time before build time, advancing clock. [ 11.179406] cgroup: cgroup2: unknown option "nsdelegate" [ 11.201734] systemd[1]: systemd 241-9-gc1f8ff8+ running in system mode. (-PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 11.225618] systemd[1]: Detected architecture arm64. [ 11.270027] systemd[1]: No hostname configured. [ 11.274611] systemd[1]: Set hostname to . [ 11.284795] systemd[1]: Initializing machine ID from random generator. [ 11.364911] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 11.382243] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 11.505307] systemd[1]: /lib/systemd/system/chronyd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/chrony/chronyd.pid → /run/chrony/chronyd.pid; please update the unit file accordingly. [ 11.608143] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 11.614767] systemd[1]: Reached target Swap. [ 11.840745] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 15.653695] EXT4-fs (mmcblk0p16): mounted filesystem with ordered data mode. Opts: (null) [ 16.501883] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [ 16.510951] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 0) [ 19.297185] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.304056] eth0: 0xffffff800a85e000, 00:04:4b:e3:fa:48, IRQ 404 [ 19.361934] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.674979] Bridge firewalling registered [ 19.828349] Netfilter messages via NETLINK v0.30. [ 19.835974] ctnetlink v0.93: registering with nfnetlink. [ 19.938434] IPv6: ADDRCONF(NETDEV_UP): balena0: link is not ready balenaOS 2.43.0 255876f ttyS0 255876f login: