[0000.282] [TegraBoot] (version 00.00.2018.01-l4t-89b97a49) [0000.287] Processing in cold boot mode Bootloader 2 [0000.292] A02 Bootrom Patch rev = 1023 [0000.295] Power-up reason: pmc por [0000.298] No Battery Present [0000.301] pmic max77620 reset reason [0000.304] pmic max77620 NVERC : 0x50 [0000.308] RamCode = 0 [0000.310] Platform has DDR4 type RAM [0000.313] max77620 disabling SD1 Remote Sense [0000.318] Setting DDR voltage to 1125mv [0000.321] Serial Number of Pmic Max77663: 0x1018f1 [0000.329] Entering ramdump check [0000.332] Get RamDumpCarveOut = 0x0 [0000.335] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.341] Last reboot was clean, booting normally! [0000.345] Sdram initialization is successful [0000.349] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.355] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.361] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.367] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.373] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.379] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.385] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.390] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.407] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.413] Platform-DebugCarveout: 0 [0000.416] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.422] Non secure mode, and RB not enabled. [0000.438] Csd NumOfBlocks=0 [0000.447] Using GPT Primary to query partitions [0000.452] Loading Tboot-CPU binary [0000.458] Verifying TBC in OdmNonSecureSBK mode [0000.468] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.475] Bootloader downloaded successfully. [0000.479] Downloaded Tboot-CPU binary to 0xa0000258 [0000.484] MAX77620_GPIO5 configured [0000.487] CPU power rail is up [0000.490] CPU clock enabled [0000.494] Performing RAM repair [0000.497] Updating A64 Warmreset Address to 0xa00002e9 [0000.502] Loading NvTbootBootloaderDTB [0000.516] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.579] Bootloader DTB Load Address: 0x83000000 [0000.584] Loading NvTbootKernelDTB [0000.598] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.660] Kernel DTB Load Address: 0x83100000 [0000.666] Loading cboot binary [0000.681] Verifying EBT in OdmNonSecureSBK mode [0000.724] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.731] Bootloader downloaded successfully. [0000.737] Using BFS PT to query partitions [0000.741] Next binary entry address: 0x92c00258 [0000.746] BoardId: 3448 [0000.750] Overriding pmu board id with proc board id [0000.755] Display board id is not available [0000.771] Verifying SC7EntryFw in OdmNonSecureSBK mode [0000.822] /bpmp deleted [0000.824] SC7EntryFw header found loaded at 0xff700000 [0001.016] OVR2 PMIC [0001.018] Bpmp FW successfully loaded [0001.023] WB0 init successfully at 0xff780000 [0001.027] Set NvDecSticky Bits [0001.031] GSC2 address ff53fffc value c0edbbcc [0001.037] GSC MC Settings done [0001.040] TOS Image length 53680 [0001.043] Monitor size 53680 [0001.046] OS size 0 [0001.052] Secure Os AES-CMAC Verification Success! [0001.056] TOS image cipher info: plaintext [0001.060] Loading and Validation of Secure OS Successful [0001.076] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.081] NvTbootPackSdramParams: start. [0001.086] NvTbootPackSdramParams: done. [0001.089] Tegraboot started after 213010 us [0001.093] Basic modules init took 565209 us [0001.097] Sec Bootdevice Read Time = 57 ms, Read Size = 2292 KB [0001.103] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.109] Next stage binary read took 11908 us [0001.113] Carveout took -23608 us [0001.116] CPU initialization took 349415 us [0001.120] Total time taken by TegraBoot 902924 us [0001.125] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):a28d87f09 NOTICE: BL31: Built : 16:52:46, Jul 16 2019 ERROR: Error initializing runtime service trusty_fast [0001.247] RamCode = 0 [0001.252] LPDDR4 Training: Read DT: Number of tables = 2 [0001.257] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.269] EMC Training Successful [0001.272] 408000 not found in DVFS table [0001.279] RamCode = 0 [0001.282] DT Write: emc-table@204000 succeeded [0001.288] DT Write: emc-table@1600000 succeeded [0001.292] LPDDR4 Training: Write DT: Number of tables = 2 [0001.332] [0001.333] Debug Init done [0001.336] Marked DTB cacheable [0001.339] Bootloader DTB loaded at 0x83000000 [0001.344] Marked DTB cacheable [0001.346] Kernel DTB loaded at 0x83100000 [0001.350] DeviceTree Init done [0001.362] Pinmux applied successfully [0001.366] gicd_base: 0x50041000 [0001.370] gicc_base: 0x50042000 [0001.373] Interrupts Init done [0001.377] Using base:0x60005090 & irq:208 for tick-timer [0001.382] Using base:0x60005098 for delay-timer [0001.386] platform_init_timer: DONE [0001.390] Timer(tick) Init done [0001.394] osc freq = 38400 khz [0001.398] [0001.399] welcome to cboot [0001.401] [0001.402] Cboot Version: 00.00.2018.01-t210-3a168c35 [0001.407] calling constructors [0001.410] initializing heap [0001.413] initializing threads [0001.416] initializing timers [0001.419] creating bootstrap completion thread [0001.423] top of bootstrap2() [0001.426] CPU: ARM Cortex A57 [0001.429] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.434] initializing platform [0001.437] Scratch reg 37 & 271 initial value set.. [0001.443] cboot:secure-pmc present [0001.493] config for ddr50 mode completed [0001.497] sdmmc bdev is already initialized [0001.501] Enable APE clock [0001.503] Un-powergate APE partition [0001.507] of_register: registering tegra_udc to of_hal [0001.512] of_register: registering tegra_udc to of_hal [0001.517] of_register: registering inv20628-driver to of_hal [0001.523] of_register: registering ads1015-driver to of_hal [0001.528] of_register: registering lp8557-bl-driver to of_hal [0001.534] of_register: registering bq2419x_charger to of_hal [0001.540] of_register: registering cpc to of_hal [0001.544] of_register: registering bq27441_fuel_gauge to of_hal [0001.556] gpio framework initialized [0001.559] of_register: registering tca9539_gpio to of_hal [0001.565] of_register: registering tca9539_gpio to of_hal [0001.570] of_register: registering i2c_bus_driver to of_hal [0001.576] of_register: registering i2c_bus_driver to of_hal [0001.581] of_register: registering i2c_bus_driver to of_hal [0001.587] of_register: registering i2c_bus_driver to of_hal [0001.592] pmic framework initialized [0001.596] of_register: registering max77620_pmic to of_hal [0001.601] regulator framework initialized [0001.605] of_register: registering tps65132_bl_driver to of_hal [0001.611] initializing target [0001.617] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.625] fixed regulator driver initialized [0001.643] initializing OF layer [0001.646] NCK carveout not present [0001.649] Skipping dts_overrides [0001.653] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.669] I2C Bus Init done [0001.671] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.681] I2C Bus Init done [0001.684] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.694] I2C Bus Init done [0001.697] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.707] I2C Bus Init done [0001.710] of_children_init: Ops found for compatible string maxim,max77620 [0001.720] max77620_init using irq 118 [0001.725] register 'maxim,max77620' pmic [0001.729] gpio_driver_register: register 'max77620-gpio' driver [0001.736] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.746] I2C Bus Init done [0001.750] NCK carveout not present [0001.753] shim_invoke: No NCT, Calling dts updates [0001.764] Find /host1x/i2c@7000c000's alias i2c0 [0001.768] get eeprom at 1-a0, size 256, type 0 [0001.777] Find /i2c@7000c500's alias i2c2 [0001.781] get eeprom at 3-a0, size 256, type 0 [0001.785] get eeprom at 3-ae, size 256, type 0 [0001.790] pm_ids_update: Updating 1,a0, size 256, type 0 [0001.795] I2C slave not started [0001.798] I2C write failed [0001.801] Writing offset failed [0001.804] eeprom_init: EEPROM read failed [0001.808] pm_ids_update: eeprom init failed [0001.812] pm_ids_update: Updating 3,a0, size 256, type 0 [0001.842] pm_ids_update: The pm board id is 3448-0002-400 [0001.848] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0001.856] pm_ids_update: pm id update successful [0001.860] pm_ids_update: Updating 3,ae, size 256, type 0 [0001.866] I2C slave not started [0001.869] I2C write failed [0001.871] Writing offset failed [0001.875] eeprom_init: EEPROM read failed [0001.878] pm_ids_update: eeprom init failed [0001.909] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.914] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0001.923] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0001.928] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0001.937] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:dd:37 [0001.943] Plugin Manager: Parse ODM data 0x00094000 [0001.953] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0001.974] Find /host1x/i2c@7000c000's alias i2c0 [0001.978] get eeprom at 1-a0, size 256, type 0 [0001.987] Find /i2c@7000c500's alias i2c2 [0001.991] get eeprom at 3-a0, size 256, type 0 [0001.995] get eeprom at 3-ae, size 256, type 0 [0002.000] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.005] I2C slave not started [0002.008] I2C write failed [0002.011] Writing offset failed [0002.014] eeprom_init: EEPROM read failed [0002.018] pm_ids_update: eeprom init failed [0002.022] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.052] pm_ids_update: The pm board id is 3448-0002-400 [0002.058] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.065] pm_ids_update: pm id update successful [0002.070] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.075] I2C slave not started [0002.078] I2C write failed [0002.081] Writing offset failed [0002.084] eeprom_init: EEPROM read failed [0002.088] pm_ids_update: eeprom init failed [0002.118] Chip UID is 0000000164447640040000000f0684c0 [0002.123] Add serial number:14228190186940c08406 as DT property [0002.131] Applying platform configs [0002.137] platform-init is not present. Skipping [0002.142] calling apps_init() [0002.157] Found 14 GPT partitions in "sdmmc3_user" [0002.162] Proceeding to Cold Boot [0002.165] starting app android_boot_app [0002.169] Device state: unlocked [0002.172] display console init [0002.181] could not find regulator [0002.204] hdmi cable not connected [0002.207] is_hdmi_needed: HDMI not connected, returning false [0002.213] hdmi is not connected [0002.216] sor0 is not supporteDT entry for leds-pwm not found d[0002.225] [0002.226] display_console_init: no valid display out_type [0002.234] subnode volume_up is not found ! [0002.238] subnode back is not found ! [0002.241] subnode volume_down is not found ! [0002.246] subnode menu is not found ! [0002.249] Gpio keyboard init success [0002.296] found decompressor handler: lz4-legacy [0002.310] decompressing blob (type 1)... [0002.344] display_resolution: No display init [0002.348] Failed to retrieve display resolution [0002.352] Could not load/initialize BMP blob...ignoring [0002.402] decompressor handler not found [0002.406] load_firmware_blob: Firmware blob loaded, entries=2 [0002.411] se_aes_verify_sbk_clear: Error [0002.415] bl_battery_charging: connected to external power supply [0002.422] xusb is supported [0002.428] error while finding nvidia,portmap [0002.434] could not find regulator [0002.937] xusb blob version 0 size 124416 [0002.941] firmware size 124416 [0002.946] Firmware timestamp: 0x5cd2a472, Version: 50.22 release [0002.959] xhci0: 64 bytes context size, 32-bit DMA [0002.999] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.019] uhub0: on usbus0 [0003.669] uhub0: 9 ports with 9 removable, self powered [0004.669] failed to get HID devices [0004.672] failed to init xhci or no usb device attached [0004.680] display_console_ioctl: No display init [0004.684] switch_backlight failed [0004.693] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0004.701] MSC Partition not found [0004.710] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0004.718] USP partition read failed! [0004.721] blob_init: blob-partition USP header read failed [0004.727] android_boot Unable to update recovery partition [0004.732] kfs_getpartname: name = LNX [0004.736] Loading kernel from LNX [0004.761] Verifying boot image in OdmNonSecureSBK mode [0004.804] kernel load address: 0x80080000, size: 482032 bytes [0004.810] ramdisk load address: 0x84100000, size: 0 bytes [0004.816] load kernel from storage [0004.825] decompressor handler not found [0004.844] Successfully loaded kernel and ramdisk images [0004.851] display_resolution: No display init [0004.855] Failed to retrieve display resolution [0004.859] bmp blob is not loaded and initialized [0004.864] Failed to display boot-logo [0004.868] NCK carveout not present [0004.871] Skipping dts_overrides [0004.874] NCK carveout not present [0004.877] shim_invoke: No NCT, Calling dts updates [0004.888] Find /host1x/i2c@7000c000's alias i2c0 [0004.893] get eeprom at 1-a0, size 256, type 0 [0004.901] Find /i2c@7000c500's alias i2c2 [0004.905] get eeprom at 3-a0, size 256, type 0 [0004.910] get eeprom at 3-ae, size 256, type 0 [0004.914] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.919] I2C slave not started [0004.922] I2C write failed [0004.925] Writing offset failed [0004.928] eeprom_init: EEPROM read failed [0004.932] pm_ids_update: eeprom init failed [0004.936] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.966] pm_ids_update: The pm board id is 3448-0002-400 [0004.973] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0004.980] pm_ids_update: pm id update successful [0004.985] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.990] I2C slave not started [0004.993] I2C write failed [0004.996] Writing offset failed [0004.999] eeprom_init: EEPROM read failed [0005.003] pm_ids_update: eeprom init failed [0005.033] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.039] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0005.047] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0005.053] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0005.061] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:dd:37 [0005.067] Plugin Manager: Parse ODM data 0x00094000 [0005.077] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.092] Add serial number:14228190186940c08406 as DT property [0005.101] "bpmp" doesn't exist, creating [0005.107] Updated bpmp info to DTB [0005.111] Updated initrd info to DTB [0005.115] "proc-board" doesn't exist, creating [0005.120] Updated board info to DTB [0005.124] "pmu-board" doesn't exist, creating [0005.129] Updated board info to DTB [0005.132] "display-board" doesn't exist, creating [0005.138] Updated board info to DTB [0005.141] "reset" doesn't exist, creating [0005.146] Updated reset info to DTB [0005.149] display_console_ioctl: No display init [0005.154] display_console_ioctl: No display init [0005.158] display_console_ioctl: No display init [0005.163] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 [0005.197] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.209] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0005.222] Updated bootarg info to DTB [0005.226] Adding uuid 0000000164447640040000000f0684c0 to DT [0005.232] Adding eks info 0 to DT [0005.237] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0005.243] Updated memory info to DTB [0005.251] set vdd_core voltage to 1075 mv [0005.255] setting 'vdd-core' regulator to 1075000 micro volts [0005.279] could not find regulator [0005.283] Found secure-pmc; disable BPMP U-Boot 2016.07-gd917e08cec (Jul 16 2019 - 16:52:59 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. MMC: no card present ** Bad device mmc 1 ** Hit any key to stop autoboot: 1  0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 733 bytes read in 123 ms (4.9 KiB/s) L4T boot options 1: primary kernel Enter choice: 1: primary kernel Retrieving file: /boot/initrd 5562393 bytes read in 184 ms (28.8 MiB/s) Retrieving file: /boot/Image 34179080 bytes read in 806 ms (40.4 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831753c3 Starting kernel ... [ 1.025989] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.537743] Host read timeout at address 545c00c4 [ 1.768004] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.775564] imx219 6-0010: board setup failed [ 2.183165] cgroup: cgroup2: unknown option "nsdelegate" [ 3.169995] using random self ethernet address [ 3.174546] using random host ethernet address [ 3.207187] using random self ethernet address [ 3.212372] using random host ethernet address [ 3.460125] random: crng init done [ 3.463532] random: 7 urandom warning(s) missed due to ratelimiting [ 6.021673] Please complete system configuration setup on /dev/ttyGS0 to proceed...